- 7 NEW!!! 30 degrees Poly-carbonate Grips w/adhesive back
- for ANH Graflex or MPP
- 92mm in length
- 3M double-stick tape
Lead time: 1-2 weeks
-
-
- 6 NEW!!! Pre-Notched Poly-carbonate Grips w/adhesive back
- 92mm in length
- 3M double-stick tape
Lead time: 1-2 weeks
-
- 6 Pre-Notched Poly-carbonate Grips w/adhesive back
- 1 Translucent Circuit Board
- 1 Kobold Clip & D-ring
Now w/Translucent Card (NEW pics coming soon)
Lead time: 1 week
-
- 7 NEW!!! 30 degrees Poly-carbonate Grips w/adhesive back
- 1 Calc Bubble Lense
- 1 Dual-hole Clip w/D-ring & two (2) rivets
Lead time 1-2 weeks
-
- 6 NEW!!! Pre-Notched Poly-carbonate Grips w/adhesive back
- 6 Exactra-sized Black-Oxide Philips Pan-Head Screws
- 1 Slothfurnace Double-sided OTIS Card
- 1 Kobold Clip w/D-ring & two (2) rivets
Lead time: 1-2 weeks
-
Out of stock
- This 3-Cell Bottom comes with grips & d-ring attached.
- Correct Angled Grips, D-Ring w/Square-drive “Roberston” screw & Bubbles
- "Folmer New York" stamped on 3-cell bottom.
- Also includes 7-bubble strip.
Due to the Corona Virus slowing many shops & projects down, there is no available ETA on these grips. Please check back at a later time.
-
Out of stock
- This 3-Cell Bottom comes with grips & d-ring attached.
- Correct alignment of grips for proper placement on your top-shell.
- "Folmer New York" stamped on 3-cell bottom.
- "NEW" will be visible to the left of the kobold.
- Also includes Double-Sided Circuit Board.
Lead time: 1-2 weeks
-
- This 3-Cell Bottom comes with grips & d-ring attached.
- Correct alignment of grips for proper placement on your top-shell.
- "Folmer New York" stamped on 3-cell bottom.
- NEW!!!: now comes with gold/translucent card (new pic coming soon).
Lead time: 1-2 weeks
-
- This 3-Cell Bottom comes with grips & d-ring attached.
- Correct alignment of grips for proper placement on your top-shell.
- "Folmer New York" stamped on 3-cell bottom.
- Includes translucent/gold card.
Lead time: 1-2 weeks
-
- Replicated from an original Graflex 3-Cell battery holder.
- "Folmer NewYork" stamped on 3-cell bottom
Lead time: 1-2 weeks
**While this battery can has a nice clean finish, it is NOT offered as flawless. Tiny imperfections may still be present.
-
Sale!
Out of stock
- Gen.1 : 1" blade holder
- Black anodized aluminum
- Threaded for 10-32 thumb-screw "glass" eye or red button (not included)
- Through-holes in thumb screw area to allow for light
- 3-point 4-40 set-screw chassis (not included) system underneath
- NO hardware included. This is only the blade adapter.
* NOTE: this will also work with the Gen.2 Graflex, but brass-pin holes will be slightly off-center.
Lead Time: 1-2 weeks
-
- Replicated from an original Graflex Glass Eye
- Made to exact measurements
- Knurling sanded down to expose brass
- This is a great collectible for both Camera Collectors and sci-fi fans
Lead time: 1-2 weeks