CONVERSION KITS

//CONVERSION KITS
    • Replicated from an original Graflex Red Button
    • Made to exact measurements
    • This is a great collectible for both Camera Collectors and sci-fi fans
    • Working button

    Lead time: 1-2 weeks

  • Sale!

    Gen.1 Graflex: 7/8″ Blade Holder

    Rated 5.00 out of 5
    $35.00 $29.99
    • Gen.1 : 7/8" blade holder
    • Black anodized aluminum
    • Threaded for 10-32 thumb-screw "glass" eye or red button (not included)
    • Through-holes in thumb screw area to allow for light
    • 3-point 4-40 set-screw chassis (not included) system underneath
    • NO hardware included. This is only the blade adapter.

    * NOTE: this blade holder also work with the Gen.2 Graflex, but brass-pin holes will be slightly off-center.

    Lead Time: 1-2 weeks

    • 6 Pre-Notched Poly-carbonate Grips w/adhesive back
    • 6 Steel Set-Screws & 6 Black-Oxide Philips Pan-Head Screws
    • 1 Slothfurnace DOUBLE-SIDED Circuit Board
    • 1 Kobold Clip & D-ring

    Lead time: 1 week

    • 6 Pre-Notched Poly-carbonate Grips w/adhesive back
    • 1 Translucent Circuit Board
    • 1 Kobold Clip & D-ring

    Now w/Translucent Card (NEW pics coming soon)

    Lead time: 1 week

  • Out of stock
    • 7 Poly-carbonate Grips w/adhesive back
    • 1 Calc Bubble Lense
    • 1 Clip & D-ring w/Robertson screw

    New grip arrival has been pushed back to mid-late February. The December samples were excellent, but still needed a bit of tweaking. Thank you for your patience as I try to get these as accurate as possible.

  • Sale!

    Gen.1 Graflex: 1″ Blade Holder

    Rated 5.00 out of 5
    $35.00 $29.99
    • Gen.1 : 1" blade holder
    • Black anodized aluminum
    • Threaded for 10-32 thumb-screw "glass" eye or red button (not included)
    • Through-holes in thumb screw area to allow for light
    • 3-point 4-40 set-screw chassis (not included) system underneath
    • NO hardware included. This is only the blade adapter.

    * NOTE: this will also work with the Gen.2 Graflex, but brass-pin holes will be slightly off-center.

    Lead Time: 1-2 weeks

    • Replicated from an original Graflex 3-Cell battery holder.
    • "Folmer NewYork" stamped on 3-cell bottom

    Lead time: 1-2 weeks

    • This 3-Cell Bottom comes with grips & d-ring attached.
    • Correct alignment of grips for proper placement on your top-shell.
    • "Folmer New York" stamped on 3-cell bottom.
    • "NEW" will be visible to the left of the kobold.
    • Also includes Double-Sided Circuit Board.

    Lead time: 1-2 weeks

  • Out of stock
    • This 3-Cell Bottom comes with grips & d-ring attached.
    • Correct Angled Grips, D-Ring w/Square-drive “Roberston” screw & Bubbles
    • "Folmer New York" stamped on 3-cell bottom.
    • Also includes 7-bubble strip.

    New grip arrival has been pushed back to mid-late February. The December samples were excellent, but still needed a bit of tweaking. Thank you for your patience as I try to get these as accurate as possible.

  • Out of stock
    • 7-piece grip set for Graflex or MPP - circa 1977
    • 30 degree angles pre-cut
    • 92mm in length
    • Strong double-stick tape

    New grip arrival has been pushed back to mid-late February. The December samples were excellent, but still needed a bit of tweaking. Thank you for your patience as I try to get these as accurate as possible.

    • Replicated from an original Graflex Glass Eye
    • Made to exact measurements
    • Knurling sanded down to expose brass
    • This is a great collectible for both Camera Collectors and sci-fi fans

    Lead time: 1-2 weeks

    • Replicated from an Original Vintage Kobold
    • Made to exact measurements
    • Accurate textured finish
    • Includes one (1) Kobold clip w/d-ring & two (2) 1/8" (3mm) medium rivets
    • This is a great collectible for both Camera Collectors and sci-fi fans
    • *Rivet holes will need to be enlarged slightly since Kobolds are bored smaller

    Lead time: 1-2 weeks