CONVERSION KITS

//CONVERSION KITS
    • Stainless Steel - 10-32 3/8"
    • One (1) Square-drive "Robertson" Screw
    • D-ring NOT included

    Lead time: 1 week

  •  
    • Also replicated from an original Graflex Red Button.
    • Has a slightly deeper angle around button than a Vintage Button.
    • This is a great collectible for both Camera Collectors and sci-fi fans.
    • Working button.

    Lead time: 1-2 weeks

    • Replicated from an original Graflex Red Button
    • Made to exact measurements
    • This is a great collectible for both Camera Collectors and sci-fi fans
    • Working button

    Lead time: 1-2 weeks

    • Replicated from an original Graflex Glass Eye
    • Made to exact measurements
    • This is a great collectible for both Camera Collectors and sci-fi fans

    Lead time: 1-2 weeks

    • Replicated from an original Graflex Folmer Eye
    • Made to exact measurements
    • Stainless Steel
    • This is a great collectible for both Camera Collectors and sci-fi fans

    Lead time: 1-2 weeks

    • Replicated from an original Graflex Glass Eye
    • Made to exact measurements
    • Knurling sanded down to expose brass
    • This is a great collectible for both Camera Collectors and sci-fi fans

    Lead time: 1-2 weeks

  • Sale!
    Out of stock

    Gen.1 Graflex: 7/8″ Blade Holder

    Rated 5.00 out of 5
    $35.00 $29.99
    • Gen.1 : 7/8" blade holder
    • Black anodized aluminum
    • Threaded for 10-32 thumb-screw "glass" eye or red button (not included)
    • Through-holes in thumb screw area to allow for light
    • 3-point 4-40 set-screw chassis (not included) system underneath
    • NO hardware included. This is only the blade adapter.

    * NOTE: this blade holder also work with the Gen.2 Graflex, but brass-pin holes will be slightly off-center.

    Lead Time: 1-2 weeks

  • Sale!

    Gen.1 Graflex: 1″ Blade Holder

    Rated 5.00 out of 5
    $35.00 $29.99
    • Gen.1 : 1" blade holder
    • Black anodized aluminum
    • Threaded for 10-32 thumb-screw "glass" eye or red button (not included)
    • Through-holes in thumb screw area to allow for light
    • 3-point 4-40 set-screw chassis (not included) system underneath
    • NO hardware included. This is only the blade adapter.

    * NOTE: this will also work with the Gen.2 Graflex, but brass-pin holes will be slightly off-center.

    Lead Time: 1-2 weeks

    • Replicated from an Original Vintage Kobold
    • Made to exact measurements
    • Accurate textured finish
    • Includes one (1) Kobold clip w/d-ring & two (2) 1/8" (3mm) medium rivets
    • This is a great collectible for both Camera Collectors and sci-fi fans
    • *Rivet holes will need to be enlarged slightly since Kobolds are bored smaller

    Lead time: 1-2 weeks

    • One (1) Stainless Steel D-Ring
    • One (1) Square-drive "Robertson" Screw: 10-32 3/8"

    Lead time: 1 week

    • Replicated from an original Graflex 3-Cell battery holder.
    • "Folmer NewYork" stamped on 3-cell bottom

    Lead time: 1-2 weeks

  • Converted 3-Cell Bottom #8

    Rated 5.00 out of 5
    $110.00
    • This 3-Cell Bottom comes with grips & d-ring attached.
    • Correct alignment of grips for proper placement on your top-shell.
    • "Folmer New York" stamped on 3-cell bottom.
    • Includes translucent/gold card.

    Lead time: 1-2 weeks